轧机垂直系统动力学参数辨识

 针对轧机垂直系统动力学参数可信度不足等问题，提出一种基于实测数据的改进粒子群算法辨识轧机垂直系统动力学参数的方法。首先,将轧机垂直系统刚度和阻尼考虑成达芬振子和范德波尔振子，构建轧机垂直系统非线性动力学模型，并对粒子群算法进行改进；然后，通过数值仿真算例辨识得到系统在感染噪声和不含噪声时的动力学参数，验证了该算法的有效性；最后，以现场某轧机垂直系统为研究对象，基于现场实测数据，应用该算法进行辨识，得到了轧机垂直系统动力学参数估计，通过实测位移、速度和加速度信号分别与辨识后的位移、速度和加速度信号进行对比，证明该方法辨识轧机垂直系统动力学参数结果可靠，具有一定的工程应用价值。     

积分中值屈服准则解析厚板轧制椭圆速度场

为解决非线性Mises比塑性功率积分困难以及由此导致的轧制功率解析式难以获得的问题,本文通过建立并利用线性比塑性功率表达式对提出的椭圆速度场进行能量分析,得到了轧制力能参数的解析解.文中通过对变角度屈服函数求积分中值,构建了一个新的屈服准则,它是主应力分量的线性组合,在π平面上的轨迹是逼近Mises圆的等边非等角的十二边形,其基于Lode参数表达式的理论结果也与实验数据吻合较好.同时,根据厚板轧制时金属流动速度从入口到出口逐渐增大的特点,提出了水平速度分量满足椭圆方程的速度场,该速度场满足运动许可条件.通过相应的轧制能量分析,获得了基于线性屈服准则的内部变形功率以及基于应变矢量内积法上的摩擦功率与剪切功率.在此之上,通过泛函的极值变分导出了轧制力矩、轧制力以及应力状态系数的解析解,并与现场实测数据进行了对比,结果表明利用本文提出的屈服准则与速度场所建立的轧制力矩与轧制力模型与实测值吻合较好,其中轧制力误差小于5.3%,轧制力矩误差在6%左右.     

发夹式换热器管束流致振动数值模拟研究

运用计算流体力学方法,采用ANSYS CFX软件对发夹式换热器的壳侧流场进行了三维数值模拟。流场计算中采用多孔介质模型对管束区域进行简化,分析了壳侧流场的速度分布,结果表明:直管段部分的流体湍流强度大于弯管段,且外层管束所在区域为高流速区,受流体冲刷严重。结合流场信息,通过功率谱生成随机激振力,采用ABAQUS软件模拟计算了湍流激振下管束的振动响应,结果显示管束的面外均方根位移远大于面内位移,且弯管部分的振动位移最大。该研究结果可为发夹式换热器的性能分析和优化设计提供参考和依据。     

YC12VC型高速柴油机发火顺序的分析研究

基于AVL-EXCITE软件搭建了YC12VC发电用高速柴油机轴系动力学模型,其模拟值与试验值吻合性较好,验证了该模型可以较好地模拟不同工况条件下轴系的运动情况。基于平衡性和均匀发火等原则,设计了8种不同的发火顺序,并针对轴承受力、轴承润滑、轴系扭振和转速不均匀性开展影响规律研究。结果表明:通过发火顺序的优化,在保证最大主轴承负荷和最小油膜厚度满足设计要求的前提下,标定工况下的曲轴扭振总振幅从0.465°降低到0.259°,转速不均匀系数从0.018降低到0.009。     

考虑流固耦合的管道机器人冲击环焊缝过程动力学建模与分析

以管道机器人（Pipeline inspection gauge，PIG）为载体的内检测技术是保障油气管道安全运输的重要手段。针对管内高压流体作用下，管道机器人在冲击管内环焊缝过程中产生的动力学行为突变问题。建立了管道周向受限空间中基于Kelvin弹簧阻尼的管道机器人密封盘等效动力学模型，结合管道机器人本体建立了多体系管道机器人动力学模型；详细推导了管道机器人轴向振动微分方程，以及管内流体的流动方程；并使用Matlab/Simulink与Adams进行流固耦合仿真，作为重要的工艺参数之一，研究了管道机器人速度改变时，其在冲击环焊缝过程中的动力学响应情况。结果表明：所建立的密封盘及管道机器人动力学模型能够很好地表征密封盘在管道轴向、径向以及周向的力学特性；运行速度越快，管道机器人通过环焊缝引起的轴向振动越剧烈，冲击振动越明显；而垂向和俯仰振动现象随运动速度增大而显著减弱。     

台阶式泄洪槽水工模型试验研究

为验证山西省某森林公园台阶式消能泄洪槽设计的合理性,通过模型试验研究了该消能泄洪槽不同流量工况下的流态、台阶平面压力、流速分布及消能效率。结果表明,在试验流量范围内,泄槽内为跌落水流和过渡水流,掺气不明显;台阶平面压力变化范围为-9.7~24.4kPa,当流量为6m^3/s时,出现最大负压9.702kPa;除#3消力池进口处外,三段台阶式消能段均为泄槽底部流速较小,对泄槽底部冲刷较小,泄槽水流表面流速最大;在不同流量下台阶式泄槽+消力池联合消能率均超过了90%,其中大部分能量消散在溢洪道台阶上。研究成果可为类似工程提供参考。     

Vibration suppression for monopile and spar‐buoy offshore wind turbines using the structure‐immittance approach

Offshore wind turbines have the potential to capture the high‐quality wind resource. However, the significant wind and wave excitations may result in excessive vibrations and decreased reliability. To reduce vibrations, passive structural control devices, such as the tuned mass damper (TMD), have been used. To further enhance the vibration suppression capability, inerter‐based absorbers (IBAs) have been studied using the structure‐based approach, that is, proposing specific stiffness‐damping‐inertance elements layouts for investigation. Such an approach has a critical limitation of being only able to cover specific IBA layouts, leaving numerous beneficial configurations not identified. This paper adopts the newly introduced structure‐immittance approach, which is able to cover all network layout possibilities with a predetermined number of elements. Linear monopile and spar‐buoy turbine models are first established for optimisation. Results show that the performance improvements can be up to 6.5% and 7.3% with four and six elements, respectively, compared with the TMD. Moreover, a complete set of beneficial IBA layouts with explicit element types and numbers have been obtained, which is essential for next‐step real‐life applications. In order to verify the effectiveness of the identified absorbers with OpenFAST, an approach has been established to integrate any IBA transfer functions. It has been shown that the performance benefits preserve under both the fatigue limit state (FLS) and the ultimate limit state (ULS). Furthermore, results show that the mass component of the optimum IBAs can be reduced by up to 25.1% (7,486 kg) to achieve the same performance as the TMD.     

A novel hybridized metaheuristic technique in enhancing the diagnosis of cross-sectional dent damaged offshore platform members

Offshore jacket platforms are widely used for oil and gas extraction as well as transportation in shallow to moderate water depth. Tubular cross-sectional elements are used to construct offshore platforms. Tubular cross sections impart higher resistance against hydrodynamic forces and have high torsional rigidity. During operation, the members can be partially or fully damaged due to lateral impacts. The lateral impacts can be due to ship collisions or through the impact of falling objects. The impact forces can weaken some members that influence the overall performance of the platform. This demonstrates an urgent need to develop a framework that can accurately forecast dent depth as well as dent angle of the affected members. This study investigates the use of an adaptive metaheuristics algorithm to provide automatic detection of denting damage in an offshore structure. The damage information includes dent depth and the dent angle. A model is developed in combination with the percentage of the dent depth of the damaged member and is used to assess the performance of the method. It demonstrates that small changes in stiffness of individual damaged bracing members are detectable from measurements of global structural motion.     

喷淋液滴在空气环境下的运动特性

本文以喷淋液滴在空气环境下运动特性为工程背景，建立单个液滴在常温、常压空气环境中的动量方程，分析液滴沉降特性、追赶特性及运动轨迹行为。计算结果表明，不同喷淋液滴初始条件下，短时间内存在重力大于曳力和重力小于曳力两种情况，但最终减速液滴均会达到受力平衡状态；液滴离开喷淋头后，垂向位移均迅速增大，液滴粒径越大、初始速度越大，垂向位移增长的速率也越大，达到相同位移的用时越短；液滴尺寸、初始速度相差越大，液滴追赶所用的时间越短，追赶位移越小，液滴尺寸、初始速度越接近，液滴追赶所用的时间越长，追赶位移越大；液滴初始速度越大、初始直径越大、喷射角度越大，横向速度消失越慢，达到的横向位移越大，喷射液滴覆盖的面积也越大。计算结果有助于优化工程实际中喷淋系统的设计与布置。     

载荷谱飞行实测振动环境谱数据处理研究

通过开展飞机振动环境谱的飞行实测,获取飞机设备舱、管路、部分飞机结构等振动环境情况,经过数据处理获取能够反映飞机实际使用下的振动环境数据,给出了典型任务剖面的功率谱密度处理结果,为飞机耐久性/损伤容限优化设计提供依据,进一步提高飞行的安全性和可靠性。